TRF-950, Inputs and Outputs
Analog Red, Green, Blue
|
|
Connector type:
Impedance:
Voltage:
Inequality of output signal voltages:
Polarity:
Coupling:
Blanking level:
Offset:
Gain (Y,C):
|
BNC female
75 Ohm
0.7Vpp (at 75 Ohm resistive load)
2%
Positive
DC
0 V
100 mV
Programmable
|
Analog CR, Y, CB
|
|
Connector type:
Impedance:
Voltage:
Inequality of output signal voltages:
Polarity:
Coupling:
Blanking level:
Offset:
Gain (Y,C):
|
BNC female (alternative function of Red, Green and Blue output)
75 Ohm
0.7Vpp (at 75 Ohm resistive load)
2%
Positive
DC
0 V
100 mV
Programmable
|
Analog Y, C
|
|
Connector type:
Impedance:
Voltage Y:
Voltage C:
Inequality of output signal voltages:
Polarity:
Coupling:
Blanking level:
Offset:
Note:
|
BNC female (alternative function of Red, Green and Blue output)
75 Ohm
1Vpp (at 75 Ohm resistive load)
0.85Vpp (at 75 Ohm resistive load)
2%
Positive
DC
0 V
100 mV
Programmable
|
Analog CVBS
|
|
Connector type:
Impedance:
Voltage:
Range:
Resolution:
Polarity:
Coupling:
Offset:
Y/C delay:
Black,blanking and burst level:
Burst position:
Chroma subcarrier:
White-to-black:
|
BNC female
75 Ohm
1 Vpp (at 75 Ohm resistive load)
0 - 1.2 V
<10 mV
Positive
DC
100 mV
<40 ns (programmable)
Programmable
rogrammable
3..5 MHz, programmable
92.5 or 100 IRE
|
DV 601/656 Port
|
|
Connector type:
Level:
Data format:
Pin 1:
Pin 9:
Pin 2:
Pin 10:
Pin 3:
Pin 11:
Pin 4:
Pin 12:
Pin 5:
Pin 13:
Pin 6:
Pin 14:
Pin 7:
Pin 15:
Pin 8:
|
D-Sub 15 pin (female)
LVTTL (3.3V)
8 bit parallel, 4:2:2, ITU-BT.656/601
Data Clock
GND
Line Gate (programmable)
Field (0..first, 1..second)
V-Sync (position programmable)
H-Sync (position programmable)
GND
D7
D6
D5
D4
D3
PD2
D1
D0
|
RF Output/s (Rear panel)
|
|
Connector type:
Impedance:
Note 1:
Note 2:
|
BNC female
75 Ohm
Up to 2 RF outputs available in single unit
according to generator options
For details and available modulators
see „Technical Specification”
|
Audio In, Out (Rear panel)
|
|
Connector type:
Level:
Output Signal:
|
Jack 3.5mm stereo (female)
see „Technical Specification”
30 Hz - 5 kHz, programmable shape and level
|
Control Port (Rear panel)
|
|
Connector type:
Pin 1:
Pin 9:
Pin 2:
Pin 10:
Pin 3:
Pin 11:
Pin 4:
Pin 12:
Pin 5:
Pin 13:
Pin 6:
Pin 14:
Pin 7:
Pin 15:
Pin 8:
RS-232 Interface:
|
D-Sub 15 pin (female)
Main +5V/50 mA (available also when power is off)
RS-232 Enable (0 or NC..disabled, 1..Enabled)
Connected to pin 1
GND
Generator TX (connect to RS-232 RX input)
GND
Generator RX (connect to RS-232 TX output)
GND
+5V/50 mA (when power is on)
GND
+3V/30mA (when power is on)
Control output (Optocoupler, Emitter, VCE<20V)
Control output (Optocoupler, Collector, Imax=20mA)
Control input (Optocoupler, Cathode, Uctrl 0V/3..9V)
Control input (Optocoupler, Anode, Ifw limited)
Baud rate 9600 bps (programmable)
8 data bits, 1 start bit, 1 stop bit, odd parity
|
USB (Rear panel)
|
|
Connector type:
Version and driver:
|
USB type B
USB 2.0, for details see „Technical Specification”
|
Test_Patterns (TRF-95x, Test Patterns) Extra_Accessories (TRF950, Extra Accessories) Inputs_and_Outputs (TRF950, Inputs and Outputs) Custom_solutions (Custom solutions) Info (TRF950, TV generator PAL-SECAM-NTSC) TRF-950_(REV09A) (PDF) FAQ (TRF950, TRF958: Frequently Asked Questions)
|